Engineering 201: DIY Recycled Suspension Bridge


engineering 201 diy recycled suspension bridge craft left brain craft brain 2affiliate disclosure As The Babe and I were driving across the Golden Gate Bridge to San Francisco the other day, she said “look at all the poles!”  I said that those are actually cables that are holding the bridge up.  And she said “How does that work?”  And I said, “uhhh, hmmm… ahh, let me check on that and get back to you.”  This post is my public service announcement for all parents crossing a bridge with an inquisitive child. golden gate bridge left brain craft brainA suspension bridge is a bridge in which the deck (the part that you drive across) is hung below suspension cables on vertical suspender cables.  Typically, suspension bridges are built with two tall towers and a cable that travels from one shore, through the two towers and to the other shore.  Vertical suspender cables hang from the main horizontal cable and hold the weight of the deck.

How can one cable hold the weight of the deck?

The weight of the deck is supported by carefully balanced forces on the two towers.  The force pulling inwards on the towers is equal to the force pulling outwards on the towers towards land.  Because the forces are balanced, the weight pulls straight down into the towers and into the ground.

What are the cables made of?

Each cable is made up of thousands of individual steel wires that are bound together.  Steel’s tensile strength improves as it is stretched into wires, so these flexible cables are stronger than a solid piece of steel of the same size.

Why are suspension bridges used instead of other kinds of bridges?

Suspension style design allows for longer spans, reduced construction costs because of reduced materials, and improved flexibility and structural integrity during earthquakes (especially important here in San Francisco!).

What are some of the most famous suspension bridges in the world?

  • Golden Gate Bridge (San Francisco, CA USA) as seen above with The Babe has been named one of the Seven Wonders of the Modern World.  It takes a team of 34 painters to maintain its characteristic “International Orange” color.
  • Akashi-Kaikyo (Pearl) Bridge (Kobe-Naruto, Japan) is the longest at nearly 2.5 miles long and the most expensive suspension bridge in the world.
  • Tsing-Ma Bridge (Hong Kong, China) is the longest two deck suspension bridge in the world and carries both rail and road traffic.  It’s main span is 4,518 ft. long.
  • Tacoma Narrows Bridge (Tacoma, WA, USA) is a suspension bridge nicknamed Galloping Gertie that collapsed due to aeroelastic flutter.  The bridge design failed to allow wind to pass through and the deck began oscillating in high winds, ultimately causing it’s collapse.  Check out this video for a fascinating look at the collapse.

Now it’s time to make your own suspension bridge!  I’ve seen a lot of these masking tape Hot Wheel race tracks out there.  We’ve even done a basic one at home ourselves, too.  This time, I wanted to do something a little more special….diy recycled suspension bridge craft closeup left brain craft brain Supplies needed:

diy recycled suspension bridge collage 1 left brain craft brain

  1. Cut a strip of cardboard out of a flattened cereal box to make your bridge.  You can tape on extra sections if you want to make a really long bridge.
  2. Punch holes along the sides of the cardboard leaving a few inches on each end without holes.  The un-holed section serves as the ramp to the “ground”.  Try to approximately line up the holes across the cardboard to help increase stability in the bridge.
  3. Thread a rubber band through each hole and loop back through itself to hold in place
  4. Create bridge towers by cutting two 1/2″ slits in one end of the each tube.  The slits should be slightly off the center and across from each other.  See the blue lines in the picture above for guidance.

diy recycled suspension bridge collage 2 left brain craft brain

  1. Start taping your race track and river.  Your river should be a bit narrower than the length of your bridge so the bridge ends can touch the “ground.”
  2. Tape down your towers.  This was the trickiest part because these towers support all the weight on the bridge just like a real suspension bridge.  Also be sure that the slits line up with the direction of the bridge.  All I have to say is thank you for repositionable tape!
  3. Cut your cables out of a length of baker’s twine.  Cut them about twice as long as your bridge because you can always cut the extra off later.
  4. Feed each piece first through the slits in the towers and then through each of the rubber bands.  Then pull the twine taught until the rubber bands stretch some and the bridge feels secure.  Tape the ends of the twine to the floor.
  5. Tape your road connectors over the bridge.  Since I often seem to be stuck in traffic at bridges in the San Francisco area, I made a toll plaza where cars can line up.

Now…  PLAY!  We had fun testing to see how strong the bridge was.  We had to buy more cars, it was so strong!! play diy recycled suspension bridge craft left brain craft brain By the way, I don’t recommend leaving the tape on the floor for extended periods of time.  Tape breaks down over time and with continued pressure as you walk on it, so it might become difficult to remove cleanly.

Want to learn more about bridges of all kinds?  Check out David Blockley’s Bridges: The Science and Art of the World’s Most Inspiring Structures.  {affiliate}

make amazing contest

This project was just made a finalist in the Scotch Products Make Amazing Contest. Like it?  Please come VOTE for me!  The prize is $5,000!!!  Just think how much tape that would buy!!!


8 Comments

Add a Comment

Your email address will not be published. Required fields are marked *